Alarko HARMONY - D Скачать руководство пользователя страница 24

Страница: 24 / 72

3.5 Turning the boiler OFF

• Turn both the CH control knob and the DHW control knob to the OFF

position.

• Turn the gas and electricity supplies to the boiler OFF.
• If the boiler is switched OFF when there is a likelihood of frost; water

in the boiler should be drained off by opening the house central heat-

ing drain tap.

3.6 Central Heating System Discharge

Do the following in case of a discharge of the central heating system

water;

• Turn on the drain tap at the bottom of the central heating system.
• Open the air release taps of radiators. Begin from top radiator to bot

tom one.

• Close the air release taps after draining the water.

ATTENTION!

It is not recommended to discharge the system except for

the necessary events.

• When the boiler is switched off at the switch on the control panel, the

word OFF appears on the display. The D.H.W and central heating

frost protection system, nevertheless, remain enabled. If the boiler

was previously on, it is switched off and the post-ventilation, pump

overrun, circulation pump and three-way valve inactivity protection

functions are enabled.

3.7. Topping-up the system with water

The water pressure in the central heating circuit must be checked in

case of a DHW request error notification. The pressure gauge located

in front of the pump, should be within the green region and must not be

less than 1 bar.

If there is insufficient water in the

boiler, the error code F0 (Table 7)

will appear on the display indicat-

ing that there is not enough water

in the system.

Figure 9 Hydraulic Group- Manual filling tab

Содержание HARMONY - D









































































Результаты поиска

Содержание HARMONY - D

Отзывы:

Alarko HARMONY - D, Инструкции по установке и обслуживанию, Страница: 24 / 72

Результаты поиска

Содержание HARMONY - D

Отзывы: