Akron EXG 400 X Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 106

background image

46

EXG 400 X GRAIN BAG UNLOADER

8-b. Transportation

The

AKRON®

model

EXG 400 X

mechanical

grain extractor requires no special configuration
changes apart from the ones explained in
paragraph 8-a. "Preparation of the Machine for
Transportation".

Figure  8.1  below  shows  the  machine  ready  for
transport  on  roads,  except  for  the  jack,  which
should  be  retracted  after  connecting  the
machine to the towing tractor. The towbar hitch,
used to tow the grain cart, is also indicated.

Figure 8.1- mechanical grain extractor ready for transport on roads

IMPORTANT:

AKRON®

EXG 400 X

mechanical grain extractor

is not

designed for road travel. Therefore,

MICRON FRESAR S.R.L.

accepts no

liability for accidents or damage that may
be caused during transport if the machine
is made to travel on roads.

If the user still needs to do this, we
recommend

consulting

national,

provincial

and

municipal

safety

regulations in force in each region.

Transport/ Operating height shims

In case of transport/operation, place the
corresponding height shim in the lift cylinder

.

Instruction

Action

Obs.

Disconnect both the hydraulic
system
and the electrical system.
Uncouple the cardan shaft.
Disconnect the tow vehicle.

Couple the pulling vehicle.
Adjust the height with the
support jack. The machine is
ready for transport.

«
...
44
45
46
47
48
...
»

Содержание EXG 400 X











































































































Отзывы:

Нет отзывов

Похожие инструкции для EXG 400 X

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Eastern Jungle Gym Страницы: 17

Бренд: Vahle Страницы: 96

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Hammer Страницы: 42

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: PASCO Страницы: 5

Бренд: Pasco Scientific Страницы: 27

Бренд: PARUS Страницы: 6

Бренд: TC Electronic Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды