AKA SIGNUM MFD 7272M CLASSIK страница 8 Скачать руководство пользователя

Страница: 8 / 65

Overall dimensions, mm: - up to 30-40 hours in economy mode

• Telescopic rod - 1200 (max.);

• Electronic unit - 120х70х115;

• Search coils - Ø 260 / Ø 380 / 150*260 / 240*320 / Ø 150

Weight of the device(without batteries): - 1400 g. (telescopic pole)

- 1160 g. (S-shaped pole)

The device allows the ability to work in water depths of up to 2,5 meters,

without submerging the control box.

GETTING STARTED

Assemble the metal detector. To do this:

- install the appliance in a metal bar;

- tighten the Collet Chuck;

- install the inner (plastic rod) sensor;

- install the rod with the sensor in a metal bar to desired length, using

the tabs and holes in the rod

- tightly and evenly wrap the sensor cable around the rod. Freely hang-

ing cables can Cause falsing;

- connect the sensor connector to the electronic unit

WARNING!

Do not over tighten the attachments and fittings for the tel-

escopic shaft. This applies in particular to the plastic bolt for the search

coil and shaft collets.

Departement of international trade:

https://aka-md.com

| +74957991510 |

[email protected]

Unlike the classic version

(plastic) Thanks to the metal

armrest, your metal detector

will not only become lighter,

but also it will be more relia-

ble in operation.

POWER SUPPLY

The device is powered using 6 AA

batteries or 6 rechargeable NIMH. Rechargeable batteries and charger

Содержание SIGNUM MFD 7272M CLASSIK


































































Результаты поиска

Содержание SIGNUM MFD 7272M CLASSIK

Отзывы:

Похожие инструкции для SIGNUM MFD 7272M CLASSIK

Бренды по названию

Популярные бренды

AKA SIGNUM MFD 7272M CLASSIK, Руководство пользователя

Результаты поиска

Содержание SIGNUM MFD 7272M CLASSIK

Отзывы:

Похожие инструкции для SIGNUM MFD 7272M CLASSIK

Бренды по названию

Популярные бренды