AJA kumo 1604 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 73

AJA kumo 1604 Скачать руководство пользователя страница 62

KUMO SDI Routers and Control Panels v4.7r1 62 www.aja.com

•  QN, IS; Gets all srcs, name & index
•  QN, D; Gets all dests, names
•  QN, ID; Gets all dests, name & indx
•  QN, L; Gets levels (hard coded as “Kumo_Lev0”)
•  QD, {destname}; Gets: protect {On/Off}, chop{=OFF}, {sourceName}, level{=

lev0}

• Qd, {destname}; Gets: protect {On/Off}, chop{=OFF}, {sourceName}, level{=

lev0}

Control:

•  TD,{destname,srcname};Takes by name
•  TI,{destIndx,srcIndx}; Takes by index
•  PR,{destname, levelmask} Sets lock for given dest.
•  UP,{destname, levelmask} Unsets lock for given dest.

RS-422 Control Specifications (Routers)

NOTE: All KUMO Routers support RS-422 control. KUMO Control Panels do not support

RS-422 control.

•  Baud Rate: 38400
•  Parity: None
•  Stop Bit: 1
•  Data Bits: 8

Serial Interface

•  1x DB-9 Female, RS-422
•  Grass Valley Native Protocol
•  9-pin D-connector pinout is as follows:

1 GND
2 TX-
3 RX+
4 GND
5

No Connection

6 GND
7 TX+
8 RX-
9 GND
Shell GND

NOTE: Older KUMO 1604, 1616, and 3232 routers with a serial number ending in -R0

have different pinouts. See

"Older Model RS-422 Adapter" on page 9

for more

information.

«
...
60
61
62
63
64
...
»

Содержание kumo 1604










































































Отзывы:

Нет отзывов