AJA kumo 1604 Скачать руководство пользователя страница 18

Страница: 18 / 73

KUMO SDI Routers and Control Panels v4.7r1 18 www.aja.com

4. Start Safari and enter 192.168.101.1 as the web address. This is the KUMO

temporary static IP address.

5. Once you’ve connected to KUMO’s web interface, reconfigure KUMO’s

network parameters as desired using the KUMO device’s NETWORK tab.

6. Restore your computer to its normal network settings using this procedure

and the IP addresses you recorded earlier.

Setup and Control from a Browser on Windows

The easiest methods of setting up a controlling a KUMO device from a PC running

Windows are:

• Setup and Control from a Browser on Windows using UPnP
• Setup and Control from a Browser on Windows using a Static IP Address

Windows: Using UPnP (Universal Plug and Play)

This method was covered earlier in this chapter.
See

"Windows PC Configuration using UPnP" on page 14

Windows Browser: Type in KUMO Static IP Address

KUMO offers a factory default static IP address. The default static IP address

is temporary and is intended only to allow an initial connection. Once you’ve

connected using the static IP, you can then enter a desired network configuration

using KUMO’s NETWORK tab.

NOTE: The default static address is temporary and will be disabled the next time KUMO

restarts. Any changes in the Network configuration will be saved upon restart.

1. Set the KUMO to its factory default IP address, using the rear Reset button

(KUMO Router) or SHIFT Buttons (KUMO CP). See

"KUMO Temporary Static IP

Address" on page 14

for this procedure.

2. Configure your computer's IP address and Subnet Mask using the standard

Windows IP configuration steps appropriate for your installed Windows

version.

IMPORTANT: Record your computer's existing TCP/IP settings. You will later need to

restore these original settings so that you can return your computer to normal

operation after this procedure.

• IP Address: 192.168.101.X (do not use .1 in the last octet)
• Subnet Mask: 255.255.255.0

3. Connect the Windows PC to KUMO’s RJ-45 port (either direct or through

your LAN)

4. Point your web browser to 192.168.101.1 as the web address. This is the

KUMO temporary static IP address.

5. Once you’ve connected to KUMO’s web interface, reconfigure KUMO’s

network parameters as desired using the KUMO device’s NETWORK tab.

6. Restore your computer to its normal network settings using this procedure

and the IP addresses you recorded earlier.

Содержание kumo 1604










































































Результаты поиска

Содержание kumo 1604

Отзывы:

AJA kumo 1604, Инструкция по установке и эксплуатации, Страница: 18 / 73

Результаты поиска

Содержание kumo 1604

Отзывы: