AJ 1000M Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 83

background image

  ∎  If  the  hose  is  curved  and  bent  extremely  when  you  set  up  the  hose,  it  will
      cause  that  air  cannot  go  and  move  around  smoothly.
  ∎  be  careful  that  the  hose  which  connects  the  air  compressor  and  the
      equipment  should  not  be  curved  or  bent  by  the  equipment.
  ∎  If  there  is  lack  of  the  compressed  air  in  the  water,  the  breaker  can  be
      damaged  seriously.

∎  Distribute  the  wires  to  operate  the  air  compressor  only  when  the  breaker  works.
∎  Turn  on  the  air  compressor  and  control  the  air  pressure  adjuster  with  checking  the  situation  of
compressed  air  in  the  breaker  after  installation.

∎ After finishing installation of the underwater operation system, turn on the air compressor and
notice following instructions before you use the breaker.

∎ Check the situation of the hose connection once again before you start working in the water.
∎ Set up the compressed air

«
...
20
21
22
23
24
...
»

Содержание 1000M




















































































Отзывы:

Нет отзывов

Похожие инструкции для 1000M

Бренд: Yaesu Страницы: 2

Бренд: VATTON Страницы: 20

Бренд: OMCN Страницы: 13

Бренд: WABCO Страницы: 24

Бренд: XPOtool Страницы: 4

Бренд: Campbell Hausfeld Страницы: 32

Бренд: Freeman Страницы: 19

Бренд: Universal Tool Страницы: 2

Бренд: Gallagher Страницы: 22

Бренд: ersa Страницы: 4

Бренд: Jet Страницы: 9

PSG12 POWER PLUS

Бренд: Milwaukee Страницы: 46

Бренд: CRH Страницы: 16

Бренд: Linear Technology Страницы: 6

Бренд: Eastwood Страницы: 3

Бренд: BorMann Страницы: 12

Бренд: Wacker Neuson Страницы: 38

Бренд: Erbauer Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды