AJ 1000M Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 83

AJ 1000M Скачать руководство пользователя страница 11

∎ Use special care to handle and store the N

2

gas cylinder as it is a high

pressurized container.
∎ Use N

2

gas only.

(5) Inspecting and charging N

2

gas into the accumulator

∎ Inspection of N

2

gas pressure in the accumulator

    ①  Remove  the  charging  valve  plug  and  tighten  the  charging  valve  fully.
          (Ensure  that  O-rings  are  installed  in  the  plug.)
    ②  Remove  the  charging  cap  and  install  the  charging  adapter.
    ③  Install  the  charging  kit  to  the  adapter.
    ④  Loosen  the  valve  gradually.  The  gas  pressure  is  indicated  on  the  gauge.
    ⑤  Close  the  valve  when  the  gas  pressure  is  normal.  If  the  gas  pressure  is  hgiher,
          repeat  loosening  and  tightening  the  relief  valve  of  charging  kit.
    ⑥  Remove  the  N2  charging  kit  and  tighten  the  charging  cap  and  plug.

∎ Charging N

2

gas pressure into the accumulator

    ①  Connect  the  charging  hose  to  the  N2  charging  kit  and  to  the  N2  gas  cylinder.
    ②  Remove  the  charging  valve  plug  and  tighten  the  charging  valve  fully.
          (Ensure  that  O-rings  are  installed  in  the  plug.)
    ③  Remove  the  charging  cap  and  install  the  charging  adapter.
    ④  Install  the  charging  kit  to  the  adapter.
    ④  Loosen  the  valve  gradually.  The  gas  pressure  is  indicated  on  the  gauge.
    ⑤  Turn  the  handle  of  the  N2  gas  cylinder  counter  clockwise  slowly  to  charge  the  gas.
    ⑥  Charge  N2  gas  in  accordance  with  the  specification  table.
    ⑦  Turn  the  handle  of  the  N2  gas  cylinder  clockwise  to  close.
    ⑧  Close  the  charging  valve.  If  the  gas  pressure  is  higher,  repeat  loosening  and  tightening  the  relief
          valve  of  charging  kit.
    ⑨  Remove  the  charging  hose,  N2  charging  kit,  adapter  and  tighten  the  charging  cap  and  plug.

«
...
9
10
11
12
13
...
»

Содержание 1000M




















































































Отзывы:

Нет отзывов