AJ 1000M Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 83

AJ 1000M Скачать руководство пользователя страница 6

    ∎  Short  term  storage
    1.  Store  breaker  in  dry  and  flat  area.  Rain  or  snow  may  cause  a  rust  in  the
          breaker.
    2.  Using  your  excavator,  place  the  breaker  horizontal  on  wooden  pallet.
    3.  The  breaker  mount  cap  area  shall  be  positioned  higher  than  the  chisel.
    4.  Remove  the  chisel  and  make  sure  the  chisel  pins,  bushes  are  well  greased.
    5.  Be  sure  that  the  hydraulic  hoses  are  plugged  to  prevent  dirty  stuffs  from
          getting  into  breaker.

  ∎  Long  term  storage
    1.  Store  breaker  in  dry  and  flat  area.  Rain  or  snow  may  cause  a  rust  in  the
          breaker.
    2.  Discharge  N2  gas  in  back  head.
    3.  Remove  the  chisel  and  push  the  piston  up  into  cylinder.  Otherwise,  the  piston
          bottom  may  get  rusted.
    4.  Make  sure  the  chisel  pins,  bushes  are  well  greased.
    5.  Be  sure  that  the  hydraulic  hoses  are  plugged  to  prevent  dirty  stuffs  from
          getting  into  breaker.
    6.  Breaker  must  be  stored  in  the  vertical  position.  Otherwise,  the  breaker  may
          cause  oil  leakage  due  to  the  seal  damage.

2. Storage

«
...
4
5
6
7
8
...
»

Содержание 1000M




















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды