Aiwa FM-LMD811 Скачать руководство пользователя страница 22

Страница: 22 / 64

– 22 –

ADJUSTMENT

1. Clock Frequency Check

Settings :

• Test point : TP2 (CLK)

Method :

Set to MW 1602kHz and check that the test
point is 2052kHz

45Hz.

2. MW VT Check

Settings :

• Test point : TP1 (VT)

Method :

Set to MW 1602kHz and check that the test point is
less than 8.0V. Then set to MW 531kHz and check
that the test point is more than 0.6V.

3. MW Tracking Adjustment

Settings :

• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location : L981 (1/3)

Method :

Set to MW 999kHz and adjust L981 (1/3) so
that the test point becomes maximum.

4. LW VT Adjustment

Settings :

• Test point : TP1 (VT)
• Adjustment location : L942

Method :

Set to LW 144kHz and adjust L942 so that the test
point becomes 1.3V

0.05V.

Then set to LW 290kHz and check that the test point is
less than 8.0V.

5. LW Tracking Adjustment

Settings :

• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L941 ........................... 144kHz
TC942 ......................... 290kHz

Method :

Set up TC942 to center before adjustment.
The level at 144kHz is adjusted to maximum by L941.
Then the level at 290kHz is adjusted
to maximum by TC942.

6. AM IF Adjustment

Settings :

• Test point : TP8 (Lch), TP9 (Rch)
• Adjustment location :
L772 ........................... 450kHz

7. FM VT Check

Settings :

• Test point : TP1 (VT)

Method :

Set to FM 108.0MHz and check that the test
point is less than 8.0V. Then set to FM
87.5 MHz and check that the test point is more
than 0.5V.

8. FM Tracking Check

Settings :

• Test point : TP8 (Lch), TP9 (Rch)

Method :

Set to FM 98.0MHz and check that the test
point is less than 13dB

9. DC Balance / Mono Distortion Adjustment

Settings :

• Test point : TP3,TP4 (DC balance)
TP8 (Lch), TP9 (Rch) (Distortion)
• Adjustment location : L771
• Input level : 60dB

Method :

Set to FM 98.0MHz and adjust L771 so that
the voltage between TP3 and TP4 becomes
0V

0.04V.

Next, check that the distortion is less than
1.3%.

TUNER SECTION

Содержание FM-LMD811

































































Результаты поиска

Содержание FM-LMD811

Отзывы:

Похожие инструкции для FM-LMD811

Бренды по названию

Популярные бренды

Aiwa FM-LMD811, Руководство по обслуживанию

Результаты поиска

Содержание FM-LMD811

Отзывы:

Похожие инструкции для FM-LMD811

Бренды по названию

Популярные бренды