Aiwa FM-LMD811 Скачать руководство пользователя страница 3

Страница: 3 / 64

– 3 –

STEREO RECEIVER RX-LMD811
<FM tuner section>
Tuning range

87.5 MHz to 108 MHz

Usable sensitivity (IHF)

16.8 dBf

Antenna terminals

75 ohms (unbalanced)

<MW tuner section>
Tuning range

531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)

Usable sensitivity

350

V/m

Antenna

Loop antenna

<LW tuner section>
Tuning range

144 kHz to 290 kHz

Usable sensitivity

1400

V/m

Antenna

Loop antenna

<Amplifier section>
Power output

Rated : 16 W + 16 W (6 ohms,
T.H.D. 1 %, 1 kHz/DIN 45500)
Reference : 20 W + 20 W (6 ohms,
T.H.D. 10 %, 1 kHz/DIN 45324)
DIN MUSIC POWER
35 W + 35 W

Outputs

SUPPER WOOFER : 1.0 V
SPEAKERS : accept speakers of
6 ohms or more
PHONES (stereo mini jack) : accepts
headphones of 32 ohms or more

<General>
Power requirements

230 V AC, 50 Hz

Power consumption

60 W

Standby power consumption

16 W (power economizing mode
deactivated)
1.7 W (power economizing mode
activated)

Dimensions of main unit

156 x 114 x 207 mm

(W x H x D)
Weight of main unit

2.8 kg

STEREO MD RECORDER / COMPACT DISC PLAYER
FM-LMD811

<Compact disc player section>
Laser

Semiconductor laser (

= 780 nm)

D-A converter

1 bit dual

Signal-to-noise ratio

85 dB (1 kHz, 0 dB)

Harmonic distortion

0.05 % (1 kHz, 0 dB)

Wow and flutter

Unmeasurable

SPECIFICATIONS

<MD recorder section>
Scanning method

Non-contact optical scanner
(Semiconductor laser application)

Recording system

Magnetic polarity modulation
overwrite system

Rotation speed

Approx. 400 to 900 rpm (CLV)

Sampling frequency

44.1 kHz

No. of channels

Stereo: 2 channels
Monaural: 1 channel

A-D, D-A converter

1-bit

Frequency

20 to 20000 Hz +0.5 - –1.5 dB

Wow and flatter

Unmeasurable

General
Inputs

TAPE IN : 500 mV
AUX IN : 500 mV
DIGITAL IN (OPTICAL) :

Outputs

LINE OUT : 500 mV

Dimensions of main unit

156 x 114 x 200.7 mm

(W x H x D)
Weight of main unit

1.8 kg

SPEAKER SYSTEM SX-LM810

Cabinet type

2 way, bass reflex (magnetic
shielded type)

Speaker

Woofer :
100 mm cone type
Tweeter :
22 mm dome type

Impedance

6 ohms

Output sound pressure level 86 dB/W/m
Dimensions

135 x 223 x 173 mm

(W x H x D)
Weight

1.8 kg

• Design and specifications are subject to change without notice.

• The word "BBE"and the "BBE symbol" are trademarks of BBE

Sound, Inc.

Under license from BBE Sound,Inc.

Содержание FM-LMD811

































































Результаты поиска

Содержание FM-LMD811

Отзывы:

Бренды по названию

Популярные бренды

Aiwa FM-LMD811, Руководство по обслуживанию

Результаты поиска

Содержание FM-LMD811

Отзывы:

Бренды по названию

Популярные бренды