Airspan FlexNET ASN-700 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 76

background image

SAFETY INSTRUCTIONS (FRENCH TRANSLATION IN APPENDIX A)

This document must be reviewed for familiarization with the product and instructions before

operation.

Verify that an un-interruptible safety earth ground exists from main power source and the

ground circuitry of the product.

Verify that correct AC power source is available for the AC adapter to produce 12...24 VDC for

the product.

Disconnect the product from operating power before cleaning.

Warning!

A professional installer must install the base station and antennas.

You are cautioned that changes or modifications not expressly approved by the part

responsible for compliance could void the user's authority to operate the equipment.

(FCC 15.21)

Note on electromagnetic emissions

This device complies with part 15 of the Federal Communications Commission (FCC) rules.
Operation is subjected to the following conditions:

1.

This device may not cause harmful interference.

2.

This device must accept any interference received including interference that cause

undesired operation

3.

Warning! Electromagnetic radiation. Please keep this product and related antennas at a
distance 20 cm from human body.

Regulatory notice

The specifications and parameters of the device described in this document are subject to

change without notice.

For American regulatory information, see www.fcc.gov. For Canadian regulatory information,

see www.ic.gc.ca.

This equipment generates, uses and radiates energy on radio frequencies and, if not

installed and used in accordance with this guide, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur

in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged
to correct the interference by one or more of the following methods:

1.

reorient or relocate the receiving antenna

2.

move the equipment and receiver farther apart

3.

connect equipment to an outlet on a circuit different from that to which the

receiver is connected

Please study first allowed regulatory guidelines shown in Appendix 5, which describe
allowed product configurations. The FlexNET ASN-700/800 product is only allowed to

be used with Airspan antennas and accessories (PSU-3 power supply) and power

dividers. In USA and Canada maximum allowed transmit power levels and channel

frequencies are shown in Appendix 5.

2

«
...
6
7
8
9
10
...
»

Содержание FlexNET ASN-700













































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNET ASN-700

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

SmartSTACK ELS100-24TXM

Бренд: Cabletron Systems Страницы: 117

Бренд: Comtrend Corporation Страницы: 4

Бренд: Linksys Страницы: 6

Бренд: MaxComm Страницы: 10

Бренд: Zhone Страницы: 53

Бренд: 3Com Страницы: 212

MULTIflight Stick

Бренд: Multiplex Страницы: 10

Бренд: Telestar Страницы: 16

Бренд: XtendLan Страницы: 17

Бренд: Hamlet Страницы: 6

Бренд: Tenda Страницы: 74

Бренд: Actisense Страницы: 14

Бренд: ActionTec Страницы: 83

Бренд: Asus Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды