Airspan FlexNET ASN-700 Скачать руководство пользователя страница 28

Страница: 28 / 76

605-0001-801 FlexNET Link Products

Enable AES encryption

If you wish to enable AES encryption, choose Enabled on this pair of radio buttons.

WPA-PSK passphrase

If AES encryption is enabled also a WPA-PSK passphrase needs to be set. The passphrase

must be the same in both devices of a link connection.

Note: Remember to click on the OK button to apply your changes, and click

Commit Settings to permanently accept the new configuration.

Interface notes (all interfaces)

Interface notes section is shown at the bottom of the screen whenever an interface is configured

as a member of an active bridge, or if Services (DHCP Server or DHCP Relay) is configured to

use the interface. Interface notes provides links to bridge or service configuration.

Routing

To set up routing information for the ASN-700/800, click on the NETWORKING>Routing link

in the configuration menu. This will open the routing table configuration page (see Figure 13).

Figure 13

The Routing table

Editing an existing route

Existing routes are displayed in the Edit routes section of the configuration screen.

To modify an existing route click in the Destination, Gateway and/or Netmask fields.

Edit the existing information and click the OK button.

The Interface field shows which interface is used for sending packets to the gateway. The

interface is the one which has an IP subnet that matches the gateway IP address. If there

is no IP subnet for the gateway IP address, the Interface field displays "Unknown!". In this

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды