Airspan FlexNET ASN-700 Скачать руководство пользователя страница 18

Страница: 18 / 76

605-0001-801 FlexNET Link Products

Associations

The number of other link units connected to this ASN-700/800 unit is displayed here.

Networking

The Networking section of the Home page contains information about the network interfaces of

your ASN-700/800:

Bridge interface. The bridge interface is a virtual interface. Binding two or more of the

remaining interfaces to the bridge will allow them to share a common IP address.

2 Ethernet ports; ethernet1 and ethernet2. Both ports are standard 10/100 Base-T

Ethernet ports, capable of a connection rate up to 100Mbit/s.

2 radio interfaces; radio1 and radio2. These interfaces consist of a pair of radio

transceiver/receivers, with an 802.11 MAC layer, used to obtain wireless connectivity.

Note: The ASN-700 comes with one Ethernet and one radio interface only, ethernet1

and radio1.

For each active interface, the following information is displayed:

MAC Address

The unique hardware identification code of the interface.

Tx Data Rate/Rx Data Rate

The rate of data being sent and received through the interface.

Action log

The ten most recent log entries are displayed at the bottom of the configuration Home page. For

more information about accessing and editing the log, see page 38.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды