Airspan FlexNET ASN-700 Скачать руководство пользователя страница 42

Страница: 42 / 76

605-0001-801 FlexNET Link Products

SOFTWARE

From time to time, firmware upgrades may become available for your ASN-700/800. Check the

Airspan website, http://www.airspan.com/, for a list of updates currently available.

Firmware updates are distributed as files. The procedure for updating the ASN-700/800

firmware is as follows:

Locate the appropriate update file on the Airspan website.

Right-click on the file name to save it on your computer. You will find it most

convenient if you save the file on the same computer that you use to access the ASN-

700/800 configuration utility.

to upload the update file to the ASN-700/800 unit (see below).

Using the Software Update page

The Software Update page provides the means of transferring the firmware update file from

your computer to the ASN-700/800 unit. To access the Software Update screen, click on the

SOFTWARE link in the configuration menu.

Figure 26

The Software update menu link

At the top of the page, the current software and hardware version numbers are displayed, along
with the unit's serial number. Near the bottom of the page, a blank text box and a pair of

buttons allow you to select and upload the new firmware (see Figure 27).

Figure 27

The Software update screen

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды