Airspan FlexNET ASN-700 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 76

background image

605-0001-801 FlexNET Link Products

NETWORKING

Click on the NETWORKING entry in the configuration menu (Figure 9) to open links to the

networking configuration pages, and the routing table.

Use these pages to set hostnames and IP addresses - or alternatively, specify a DHCP server -

for the network interfaces of your ASN-700/800. The networking configuration pages can also
be used to enable or disable interfaces, to bind interfaces to the bridge, or to set operating

parameters for the special radio interfaces.

Figure 9

The Networking menu

Note: The ASN-700 comes with one Ethernet and one radio interface only, ethernet1

and radio1.

Changing Ethernet settings

Click on the NETWORKING>ethernet1 or NETWORKING>ethernet2 link in the

configuration menu to open the configuration page for the respective Ethernet interfaces. Figure

10 shows the configuration page for the ethernet1 interface.

Figure 10

Configuring an Ethernet interface

17

«
...
21
22
23
24
25
...
»

Содержание FlexNET ASN-700













































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNET ASN-700

TokenLink 3C359B

Бренд: 3Com Страницы: 4

TokenLink 3C359B

Бренд: 3Com Страницы: 8

TokenLink 3C339

Бренд: 3Com Страницы: 2

EtherLink 3C985B-SX

Бренд: 3Com Страницы: 44

Бренд: 3Com Страницы: 88

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 111

TokenLink 3C359

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

Бренд: Abocom Страницы: 1

Бренд: Xantrex Страницы: 8

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды