Airspan FlexNET ASN-700 Скачать руководство пользователя страница 68

Страница: 68 / 76

605-0001-801 FlexNET Link Products

20. Click the Guest preferences link on the Navigation menu. Click Save. Click Restart

RoamNET.

21. Click the Statistics link on the Navigation menu. Click Update statistics configuration.

22. Configuration of the ControlNET server is ready.

23. Have two ASN-820 units and label them as bs1 and bs2.

24. Login to the web interface of bs1 via ethernet1 using the IP address 192.168.1.1.

25. Go to NETWORKING>bridge

26. Change the IP address to 192.168.255.1. Press OK.

27. Go to NETWORKING>ethernet1. Check that the IP address of bs1’s ethernet1 interface is

192.168.1.1. (When configuring bs2, change the IP address to 192.168.1.2.) Press OK.

28. Go to NETWORKING>Routing. Enter the following values. Destination: 0.0.0.0,

Netmask: 0.0.0.0, Gateway: 192.168.1.254. Click Add.

29. Go to SERVICES>DHCP Relay. Check Enable box and change the server IP address to

192.168.1.254. Press OK.

30. Go to SERVICES>RoamNET. Check Enable box and change the server IP address to

192.168.1.254. Press OK.

31. Press Commit Settings. The new settings will now be taken into use.

32. Repeat the same procedure with bs2.

33. Configuration of the base stations is now ready.

34. Connect the base stations and the ControlNET server to a network. Client terminals should

now be able to associate and communicate with the base stations.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды