manualshive.com logo in svg

Airspan AirHarmony-1000, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony-1000 Скачать руководство пользователя страница 9

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

2 

 

Warnings and Cautions 

Human Exposure to Radio Frequencies 

The AirHarmony-1000 antennas should be installed and operated from a minimum safe distance of: 

 

AirHarmony-1000 with Front Mount Antenna: 2.5m 

 

AirHarmony-1000 with External Antenna: 2.5m 

 

AirHarmony-1000 with Smart Beam Antenna (SBA): 0.5m (pending) 

Radio Interference 

This  AirHarmony-1000  generates,  uses,  and  can  radiate  radio  frequency  energy  and, if  not  installed 
and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 
communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular 
installation. If  this  equipment  does  cause  harmful  interference  to radio  or  television  reception,  which 
can be determined by turning the equipment on and off, the technician is encouraged to try to correct 
the interference by performing one or more of the following measures: 

 

Re-orientate or relocate the unit  

 

Increase separation between the eNodeBs and/or End Device 

 

Connect the equipment to an outlet on a circuit different from that to which the power source 
is connected 

Avoiding Radio Interference  

Ensure a minimum of 1-meter separation between co-located AirHarmony 1000 units. 

Modifications 

Any changes and modifications to this device that are not expressly approved by Airspan Networks 
may void the user's authority to operate the equipment. 

General 

 

Only qualified personnel should be allowed to install, replace, and service the equipment. 

 

The device cannot be sold retail, to the general public or by mail order. It must be sold to 
operators. 

 

Installation must be controlled. 

 

Installation must be performed by licensed professionals. 

 

Installation requires special training. The AirHarmony-1000 radio and antenna should be 
installed ONLY by experienced installation professionals who are familiar with local building 
and safety codes and, wherever applicable, are licensed by the appropriate government 
regulatory authorities. Failure to do so may void Airspan's product warranty and may expose 
the end user or the service provider to legal and financial liabilities. Airspan and its resellers 
or distributors are not liable for injury, damage or violation of regulations associated with the 
installation of outdoor units or antennas. 

 

The device is to be installed in a Restricted Access Location. 

Safety  

1. 

Read this guide and follow all operating and safety instructions. 

2. 

Keep all product information for future reference. 

Содержание AirHarmony-1000































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды