manualshive.com logo in svg

Airspan AirHarmony-1000, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony-1000 Скачать руководство пользователя страница 57

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

50 

 

7  Additional Installations (Non-Standard) 

7.1 Front Antenna Assembly 

Note:

 The following section is included for 

spare-parts

 or 

replacement

 assembly 

instructions as front mounted antenna variants come factory pre-assembled. 

The AirHarmony-1000 unit can be used either with a sector antenna mounted directly on the front or 
with a remotely attached antenna. The following describes the installation procedure for the front 
mounted antenna. 

For installation of a remotely mounted antenna follow the antenna manufacturer’s instructions and 
connect the antenna to the AirHarmony-1000 using the appropriate cables. (Weather-proofed N-type 
Heliax RF cables (ordered separately). 

Note:

 When a front mounted antenna is not attached to the unit (remote antenna) a 

Sunshield should be attached. Variants utilizing remotely attached antennas come 
factory pre-assembled with a sunshield. 

 

To

 

mount

 

the

 

front

 

antenna,

 

perform

 

the

 

following: 

1.  Fit the antenna to the (antenna) mounting plate. The four (4) studs on the back of the antenna 

pass through the front face of the mounting plate and are secured with the 4 sets of M4 nuts 
and washers (flat and split) included in the kit. Carefully position the lead RF cables and 
secure them in place to the eyelets on the back of the mounting plate with the provided cable 
ties. The cables are formed with a cross-over at the bottom. 

Note:

 It is recommended to place some packing material under the unit while assembling 

to protect it from scratches. 

 

2.  Attach the assembled front mounted antenna with the bracket to the AirHarmony-1000 unit 

using the M5 SEMs (2 on each side) and connect the RF cables to the N type RF ports on the 
top of the AirHarmony-1000. 

Note:

 The plate is mounted with the side slots towards the top so that the required tilt-

down can be set. 

 

Figure 61: Attaching front mount antenna assembly to AirHarmony-1000 

 

 

7.2 Connecting RF Jumper Cables to External Antenna 

Note:

 Variants utilizing remotely attached antennas are factory pre-assembled with a 

sunshield. 

 

Содержание AirHarmony-1000































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды