Airspan AirHarmony-1000 Скачать руководство пользователя страница 53

Страница: 53 / 62

AirHarmony-1000 Installation Guide

UGD-D01006

Airspan Commercial and Internal Use

Figure 52: Slide over and click

Note:

The shell should be hand tightened only. Do NOT use tools to tighten the shell.

7. Once the connector is properly installed, the cable should be positioned and secured to

minimize stress on the cable and connector.

6.5 Copper Ethernet Cable Installation

Note:

The following images are for illustration purposes only. The actual tools or

hardware may differ according to manufacturer.

The following demonstrates the recommended assembly instructions, hardware and tool requirements
for the proper Ethernet cable assembly of the Ethernet Category 5e (enhanced) (CAT5e) cable used
by Airspan products.

The Ethernet cable is connected using a standard RJ45 connector protected by a harsh environment
protective casing.

6.5.1 Hardware Requirements

The following are the cable and connectors available from Airspan.

Table 14: Hardware

Airspan Part Number

Description

CAT5e-STP-305M-R

CAT5e Ethernet Cable, 305M (1000ft), STP, Reel

RJ45-ETH-SHLD-CONN

RJ45 Ethernet Connector, Shielded

Содержание AirHarmony-1000































































Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды

Airspan AirHarmony-1000, Руководство по установке

Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды