Airspan AirHarmony-1000 Скачать руководство пользователя страница 41

Страница: 41 / 62

AirHarmony-1000 Installation Guide

UGD-D01006

Airspan Commercial and Internal Use

Figure 23: Tilt adjustment antenna

After adjusting to the required tilt amount tighten both flange nuts and both screws. The
antenna has an electrical fixed down-tilt of 1°.

5.5 LED Display

A single tri-color LED (Green/Red/Orange) appears at the bottom of the unit, providing unit status
indication. When powering up refer to the following table for indication of current status:

Table 13: LED display

Name

Color

Status

Description

Powering Up

Orange

On Continuously

Till the SW starts loading

Software loading

Green

Blinking (3Hz)

While SW is loading

Normal Operation

Green

On Continuously

Normal operation (no alarm)

Major Alarm

Red

Blinking (3Hz)

Service

not

affected

Critical Alarm
or
Sector OOS

Red

On Continuously

5.6 Connecting the Ground Cable

Connect the ground cable after attaching the grounding lug (optionally supplied by Airspan

– CBL-

GND-1M-1 and CON-LUG-GND-1) to the M6 threaded connection on the bottom of the main body
casting.

Note:

Cutting the Ground cable to the required length and crimping the grounding lug is

performed by the Installer.

Note:

The ground cable is available per meter. The lug can also be used for securing the

ground cable to the other side.

Note:

The ground surface is bare metal and needs no preparation.

Содержание AirHarmony-1000































































Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды

Airspan AirHarmony-1000, Руководство по установке

Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды