AirLive WN-151ARM Скачать руководство пользователя

Страница: 45 / 119

AirLive WN-151ARM User’s Manual

Status Screen

ADSL

Modem Status

This indicates the status of the ADSL modem component.

DownStream

Connection Speed

Displays the speed for the DownStream Connection.

UpStream

Connection Speed

Displays the speed for the Up Stream (upload) ADSL Connection.

Internet (VC1)

Connection

Method

Displays the current connection method, as set in the

Setup Wizard

Connection Status

This indicates the current status of the Internet Connection

•

Active

- Connection exists

•

Idle

- No current connection, but no error has been detected. This

condition normally arises when an idle connection is automatically

terminated.

•

Failed

- The connection was terminated abnormally. This could be

caused by Modem failure or the loss of the connection to the ISP's

server.

If there is an error, you can click the "Connection Details" button to find

out more information.

Internet IP Address

This IP Address is allocated by the ISP (Internet Service Provider). If

using a dynamic IP address and no connection currently exists, this

information is unavailable.

WAN MAC Address

It displays the MAC address for the WAN.

Connection Details

Click this button to open a sub-window and view a detailed description of

the current connection. Depending on the type of connection, a "log"

may also be available.

LAN

IP Address

The IP Address of the WN-151ARM.

Network Mask

The Network Mask (Subnet Mask) for the IP Address above.

DHCP Server

This shows the status of the DHCP Server function. The value will be

"On" or "Off".

MAC Address

This shows the MAC Address for the WN-151ARM, as seen on the LAN

interface.

Содержание WN-151ARM
























































































































Результаты поиска

Содержание WN-151ARM

Отзывы:

Похожие инструкции для WN-151ARM

Бренды по названию

Популярные бренды

AirLive WN-151ARM, Руководство пользователя

Результаты поиска

Содержание WN-151ARM

Отзывы:

Похожие инструкции для WN-151ARM

Бренды по названию

Популярные бренды