AirLive WN-151ARM Скачать руководство пользователя

Страница: 27 / 119

AirLive WN-151ARM User’s Manual

3.2 LAN Screen

Use the

LAN

hyperlink on the main menu to reach the LAN screen. An example screen is shown below.

Figure 1: LAN Screen

LAN Screen

TCP/IP

IP Address

IP address for the WN-151ARM, as seen from the local LAN. Use the default

value unless the address is already in use or your LAN is using a different IP

address range. In the latter case, enter an unused IP Address from within the

range used by your LAN.

Subnet

Mask

The default value 255.255.255.0 is standard for small (class "C") networks. For

other networks, use the Subnet Mask for the LAN segment to which the

WN-151ARM is attached (the same value as the PCs on that LAN segment).

DHCP

Server

•

If enabled, the WN-151ARM will allocate IP Addresses to PCs (DHCP

clients) on your LAN when they start up. The default (and recommended)

value is Enabled.

•

If you are already using a DHCP Server, this setting must be disabled, and

the existing DHCP server must be re-configured to treat the WN-151ARM

as the default Gateway. See the following section for further details.

•

The

Start IP Address

and

Finish IP Address

fields set the values used by

the DHCP server when allocating IP Addresses to DHCP clients. This

range also determines the number of DHCP clients supported. Enter the

desired value for the

Lease Time

, which should be between 1 and 7.

See the following section for further details on using DHCP.

Содержание WN-151ARM
























































































































Результаты поиска

Содержание WN-151ARM

Отзывы:

Похожие инструкции для WN-151ARM

Бренды по названию

Популярные бренды

AirLive WN-151ARM, Руководство пользователя

Результаты поиска

Содержание WN-151ARM

Отзывы:

Похожие инструкции для WN-151ARM

Бренды по названию

Популярные бренды