Air 486PH Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 48

Air 486PH Скачать руководство пользователя страница 33

IDE Block Mode

Select

Enabled to support

some latest IDE hard disks that

supporting multiple sector data transfer for faster performance.
In Auto mode, the BIOS will detect if the IDE drives can handle
fast data transfer mode and then programs the controller
accordingly. The Optimal default setting is

Auto.

The Fail-Safe

default setting is

Disabled

.

32-bit Xfer Primary Controller

This option is used to support the first IDE controller that can
support 32-bit data transfer by moving two consecutive words
per cycle, for better performance. Select Enabled if the
controller can support this mode, otherwise, set it to Disabled.
The Optimal and Fail-Safe settings are

Disabled

.

Set LBA Primary Controller

Most   of   early   IDE   hard   drives’   size   are   less   than   528MB
because of the limitation from PC/AT standard specification.   In
order to support more than 528MB, the Logical Block Access
(LBA)   mapping   mode   must   be   used.     When   Primary   IDE
controller card is installed, Select

Enabled

for Master IDE hard

disk that supports LBA mode for larger than 528MB capacity.
The Optimal and Fail-Safe default setting are

Disabled

.

Secondary Controller Setup

This option supports Second IDE controller present in the bus or
some IDE controllers that support dual IDE ports. The Optimal
and Fail-Safe default setting are

None

.

«
...
31
32
33
34
35
...
»

Содержание 486PH

















































Отзывы:

Нет отзывов