Air 486PH Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

Air 486PH Скачать руководство пользователя страница 18

Turbo Switch Connector

The Turbo switch (TURBO) is a 2-pin BERG strip.  It is used to
connect  the  front   panel   2-position  push   switch  to  the   system
board   speed   switching   circuitry.     The   Turbo   mode   is   set   as
default on the 486PH.

Function

TURBO

Enable TURBO Mode (Default)

Short

Disable TURBO Mode

Open

Turbo LED Connector

The Turbo LED connector (TBLED) is a 2-pin BERG strip. It is
used to connect a CPU operating frequency indicator LED from
the front panel to the system board. The pin assignments are
indicated below:

Pin

Description

1

LED Cathode ( - )

2

LED Anode (+)

Hard Disk Activity LED Connector

The hard disk activity LED connector (label as HDLED) is a 2-
pin keyed BERG strip. The LED will be on whenever there is
data transfer activity on on-board IDE bus. The connector
should be connected to the case’s front panel hard disk LED.

Pin

Description

1

LED Anode (+)

2

LED Cathode (-)

«
...
16
17
18
19
20
...
»

Содержание 486PH

















































Отзывы:

Нет отзывов