Air 486PH Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

Air 486PH Скачать руководство пользователя страница 25

Peripheral Device Connection

IDE Hard Disk Drives Connection

The 486PH supports up to 2 IDE hard disk drives on the system.
The IDE ribbon-cable is provided with the system board. Use
the cable to connect the IDE drives into 40-pin double-row
connector IDE on the board. Make sure the colored stripe on the
cable (indicating the location of pin 1) matches Pin 1 of the
connector on the mother board, as well as the Pin 1 of the Hard
drives.

Peripheral Add-on Card installation

The  486PH   support   both  PCI   slots  and  VESA   VL  bus  slots.
You can install the corresponding add-on cards into any of these
slots.     Make   sure   these   add-on   cards’   interrupts   or   DMA
channels  are  not conflicted  with each other.  The  best way to
remember is to writing down the information of all the installed
cards into the back of this manual for later reference.

Please refer to the manuals shipped with the add-on cards for
more information. Care should be taken when inserting the
cards into the slots to make sure the connectors slots are not
damaged.

«
...
23
24
25
26
27
...
»

Содержание 486PH

















































Отзывы:

Нет отзывов