background image

LoadLifter 5000 Series

MN-1053

12

ATTACHING THE LOWER BRACKET

The way the lower bracket is attached depends on the truck model. See Fig. 19 to 
determine which holes to use for inserting the carriage bolts.

1.  Push the lower bracket up against the stock U-bolts so that the legs of the lower 

bracket are locked into position around the stock U-bolts (Fig. 19). It may be 
necessary to rotate the lower bracket cup on the jounce bumper strike plate in order 
to do this. 

2.  If installing this kit on a single-rear-wheel (SRW) vehicle, use the inside position square 

holes in the lower bracket to insert the long 3/8”-16 x 10” carriage bolts (Q) through 
(Fig. 19). If installing this kit on a dual-rear-wheel (DRW) vehicle, use the outside set of 
holes to insert the carriage bolts through.

THE CARRIAGE BOLT WILL GO BETWEEN THE HARD BRAKE LINE AND THE AXLE ON 
THE DRIVER’S (LEFT) SIDE (FIG. 20). DEPENDING ON THE MODEL OF THE TRUCK, 
THE BRAKE LINE MAY GO IN BETWEEN OR BEHIND THE HARD BRAKE LINE ON THE 
PASSENGER’S (RIGHT) SIDE OF THE AXLE (FIG. 21).  

3.  Position the U-bolt (J) around the leaf spring assembly and insert it in the hole closest 

to the leaf spring stack (Fig. 21). The lower bracket flanges must be locked on the 
front and rear of the stock U-bolts holding the leaf springs to the axle. 

4.  Cap the U-bolts with two 3/8” flat washers (Z) and two 3/8”-16 nylon lock nuts (Y) 

and evenly tighten only enough to draw the bracket up against the stock U-bolt at 
this time (Figs. 20 & 21). Make sure the lower bracket rests against the stock U-bolts.

fig. 19

Push the lower 

bracket tight to the 

stock U-bolt.

Outside hole

Inside hole

NOTE

fig. 20

fig. 21

Y

J

Q

SRW 

mounting 

position 

shown.

Insert U-bolt 

in the hole 

closest to the 

leaf spring 

stack.

The carriage 

bolt goes 

between the 

brake line 

and axle on 

the left side.

E

Z

Y

Depending 

on the truck 

model, the 

carriage bolt 

might go 

between the 

brake line 

and axle or 

outside the 

brake line.

Z

CAUTION

Содержание LoadLifter 5000 Ultimate





























Отзывы: