Air innovations 99H0360-10 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 85

Air innovations 99H0360-10 Скачать руководство пользователя страница 66

66

Differential
temperature
adjustment

Setting 15

•

Press “Settings” button to advance to Setting
15

•

Press the “Up” or “Down” buttons to adjust to
the desired setpoint. This setting changes the
system/compressor turn-on temperature above
setpoint. Factory default is 1°F.

Example: Sensor reading = 55°F (13°C)

Setting 15 set to +3°F

System/compressor turns on at 58°F (14°C)

Temperature
deadband

Setting 16

•

Press “Settings” button to advance to Setting
16.

•

Press the “Up” or “Down” buttons to adjust to
the desired setpoint. This setting is the
minimal allowable temperature difference
between heating and cooling setpoints.
Maximum is 5°F (3°C), minimum is 1°F
(1°C). Factory default is 2°F (1°C).

Condensate
switch

Setting 17

•

Press “Settings” button to advance to Setting
17.

•

Press the “Up” or “Down” buttons to adjust to
the desired setpoint. This setting disables or
enables the Condensate switch. 0 (zero) is
disabled, 1 is enabled. Factory default is 0.

Reserved

Settings 18 & 19

Reserved for additional fields.

System type
defaults

Setting 20

System setting.

DO NOT CHANGE.

Reserved

Settings 21-29

Reserved for additional fields.

«
...
64
65
66
67
68
...
»

Содержание 99H0360-10






















































































Отзывы:

Нет отзывов