manualshive.com logo in svg

Air innovations 99H0360-10, Инструкция по установке, эксплуатации и обслуживанию, Страница: 32 / 85

Поделиться
Скачать
Air innovations 99H0360-10 Скачать руководство пользователя страница 32

32 
 

RISK OF PERSONAL INJURY OR DAMAGE TO EQUIPMENT 

Modification to the equipment may cause injury or damage to the equipment

. 

 

DANGER

 

 

 

✓

 

This equipment is heavy. Place the unit on the floor or on a level and 
stable surface that can support the full weight of the unit. 

✓

 

Do not modify the equipment. Modifications may cause damage to the 
equipment and will void the warranty. 

✓

 

Never place anything on top of the unit. 

✓

 

Never block or cover any of the openings or outlets to the unit. 

✓

 

Never allow anything to rest on or roll over the power cord. 

✓

 

Never place the unit where the power cord is subject to wear or abuse. 

✓

 

Do not use extension cords. 

✓

 

Never overload wall outlets. 

✓

 

Do not remove or open any cover unless the unit is turned off and the 
power cord is plugged in. 

✓

 

Use only dedicated power outlet boxes of the correct capacity and 
configuration for the unit model. 

 

 

 

CAUTION 

 

 

RISK OF PERSONAL INJURY OR DAMAGE TO EQUIPMENT 

Improper installation may result in the equipment malfunctioning and a safety hazard. 

Read all of the installation instructions before installing the Wine Guardian unit.

Содержание 99H0360-10






















































































Отзывы:

Нет отзывов