Air Change PCU Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 35

Air Change PCU Скачать руководство пользователя страница 6

Installation and Maintenance Manual

6

Lifting with a Forklift

Exercise extreme caution when lifting with a forklift. Do not exceed the height limit of the forklift and

never allow fork to lift against the bottom panel of the unit.

Make careful consideration of the unit’s centre of gravity and distribute the weight equally on both

forks. Test load to see if the weight is equally distributed. Do this by lifting the unit a few

centimetres off the floor and holding it there before lifting any further or before transporting the unit.

Lifting with a Crane

NOTE: All units should be lifted into position using slings.

Where units have to be lifted into position, installers must check the unit weight is within tolerance

of the safe working capacity of the lifting equipment.

When preparing to move the unit, always determine the unit's centre of gravity in order to equally

distribute the weight.

Spreader bars must be used between slings to prevent crushing the frame or panels. Spreader

bars and/or pipe are not supplied with units.

Spreaders whose length exceeds the largest dimension across the unit should be across the top of

the unit.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

«
...
4
5
6
7
8
...
»

Содержание PCU




































Отзывы:

Нет отзывов