Air Change PCU Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 35

Air Change PCU Скачать руководство пользователя страница 14

Installation and Maintenance Manual

14

Fans

Supply fans in standard units are aerofoil single

inlet backward inclined centrifugal impellers

with three dimensional profiled blades made

from one cast, without welds.

The fan is directly driven by high efficiency

variable speed EC (electronically commutated)

motor and controlled via 0-10 V through

constant volume air controller

The fan motor is fitted with sealed-for-life ball bearings with in-built diagnostic/service LEDs.

Heat Exchanger

The sensible heat exchanger uses counter flow with

transfer media between moulded plastic air guiding

frames for a very high efficiency and long life.

There is no cross contamination between the air paths.

The Heat Reclaim (sensible) counter flow heat

exchanger incorporated into the unit has efficiency of

80% when both airstream are of equal volume flowrate.

IMPORTANT

DO NOT ATTEMPT TO CHANGE THE LENGTH OF THE HEAT EXCHANGER BY
REMOVING END PLATES AND PLASTIC PLATES.

This can cause the media between the plates to dislodge from its position, resulting in
a lack of performance because of an increased pressure drop through the heat
exchanger or damage to the Sensible media. Any tampering with the heat exchanger
may invalidate our warranty and Air Change will not be held responsible for
compromised performance or a pressure drop.

If the heat exchanger is the incorrect length, please return to Air Change for a
replacement unit.

Heat Exchangers are constructed of plastic moulded plates with media between each plate. The

heat exchanger has been secured by end plates under pressure. Sensible heat exchanger has end

plates and corner/middle fixings of powder coated aluminium with sensible Mylar media between

the plates.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

«
...
12
13
14
15
16
...
»

Содержание PCU




































Отзывы:

Нет отзывов