Air Change PCU Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 35

Air Change PCU Скачать руководство пользователя страница 10

Installation and Maintenance Manual

10

Filters

IMPORTANT

Never operate the unit without filters fitted to the Return and Fresh Air intakes with
blower access panels removed.

Make-up air quantity (if any) is to be incorporated into outdoor air filtered airflow.

G4 panel and bag filters are included in standard units.

NOTE:

If these units are being used during construction when adhesive or sealants are in use, and

if ducts and carpets are being installed or removed, make sure all equipment is fitted and

adequately protected. We recommend using disposable or temporary filters during commissioning

and during pre

‐

hand over running.

Electrical/Electronic Connections

For power requirements and voltages, see the unit specifications.

The electrical diagram is attached on the wall of the electrical board cabinet.

Mains Power Supply and Fusing

A power supply rated at 415 V +/

‐

10% 3-phase or 240 V +/

‐

10% 1-phase, 50 Hz is required to

operate the machine within manufacturer's tolerances.

Mains cables are to be connected as per the wiring diagram.

Field wiring on the sensor and HLI communication to the controller (if any) need to be done on site.

The units require a mains circuit breaker or HRC fusing capable of handling the full load of the unit

and selected in accordance with SAA Wiring Rules to be fixed external to the unit.

A mains switch is fitted to the electrical board inside unit.

Electrical Connection and Supply Size Precaution

We recommend an isolator be mounted externally to the unit (not supplied) and a suitably sized

fuse mounted back at the distribution board to provide local isolation during service and

maintenance periods. The unit has a 3

‐

phase switch internally on the electrical board.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

«
...
8
9
10
11
12
...
»

Содержание PCU




































Отзывы:

Нет отзывов