manualshive.com logo in svg

Air Change PCU, Руководство по установке и обслуживанию, Страница: 30 / 35

Поделиться
Скачать
Air Change PCU Скачать руководство пользователя страница 30

 

 
Installation and Maintenance Manual 

 

30 

10.

 

TECHNICAL DATA 

‐

 TABLES 

Heat Exchanger Data 

Specification 

Small Heat Exchanger 

Large Heat Exchanger 

Height 

710 mm 

1290 mm 

Depth 

330 mm 

640 mm 

Width 

645 mm 

650 mm 

Weight 

25 kg/m 

75 kg/m 

Pressure Drop 

150 Pa @ 750 L/s per metre up to 
250 Pa @ 1000 L/s per metre 

120 Pa @ 1000L/s per metre up to 
150 Pa @1700 L/s per metre 

Reclaimed Heat 

Enthalpy Heat exchanger - up to 75%. 

Enthalpy Heat exchanger - up to 75%. 

Sensible Heat Exchanger - up to 80% 

Sensible Heat Exchanger - up to 80% 

Insulation 

5 mm thick black poly-ethylene with adhesive 
backing, fire resistant 

5 mm thick black poly-ethylene with 
adhesive backing, fire resistant 

Material 

Poly-propylene solvent resistant 

High impact poly-styrene solvent resistant 

Temperature Range 

Plates withstand a temperature range 
of -50°C to 150°C 

Plates withstand a temperature range 
of -50°C to 120°C 

Transfer Media 

Enthalpy media - moisture permissible. Exchanges moisture and temperature. 

Maintenance 

Supply and exhaust air must be filtered to avoid particles entering the heat exchanger 

Sandwich Panel Data 

Skins

 

CRP Colorbond 

0.6 mm  

Australian Standard 

AS 2728 Category 2 and/or 3 

Substrate 

ZINCFORM® G300 BFC Z275 1 

Pretreatment 

Corrosion resistant proprietary conversion coating 

Primer Coat 

Universal corrosion inhibitive epoxy primer. Nominal thickness 5 µm each side. 

Finish Coat 

Custom formulated system. Nominal thickness 20 µm on the top or weather side. 
The standard colour is off white. 

Backing Coat 

Custom formulated Foam Grey, specially designed to facilitate adhesion to foam 
cores. Nominal film thickness 5 µm 

Gloss 

Nominal 25% (60°) 

Dimensions

 

Width 

Standard 1200 mm (coverage) 

Length 

To design requirements (limited by handling/transportation consideration) 

Thickness 

Standard 50 mm 

Weight 

11.3 kg/m 

Panel Spans

 

Walls 

5400 mm 

Ceilings 

3000 mm 

Insulation Factors

 

R Value 

2.65 m/Kw 

Fire Hazard Properties

 

Ignitability Index 

0 (scale 0 - 20) 

Spread of Flame Index 

0 (scale 0 - 10) 

Heat Evolved Index 

0 (scale 0 - 10) 

Smoke Developed Index 

0 (scale 0 - 10) 

Cooke Industries - Phone: +64 9 579 2185    Email: [email protected]    Web: www.cookeindustries.co.nz

Содержание PCU




































Отзывы:

Нет отзывов