background image

AIM Hybrid Pulse MIG Welder -HPM-350-HD

 

 

A

IM MIG OWNER’S MANUAL Rev. 2019

 | LIMITED WARRANTY 

20 

 

LIMITED WARRANTY 

 

American  Innovative  Manufacturing  LLC  (AIM)  of  Spokane,  WA,  subject  to  the  terms  and  conditions 
described  below,  warrants  to  its  original  retail  purchaser  that  new  AIM  equipment  sold  after  the 
effective date of this limited warranty is free of defects in material and workmanship at the time  it is 
shipped  by  AIM.  THIS  WARRANTY  IS  EXPRESSLY  IN  LIEU  OF  ALL  OTHER  WARRANTIES,  EXPRESS  OR 
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. 
AIM  PRODUCTS  ARE  INTENDED  FOR  PURCHASE  AND  USE  BY  COMMERCIAL/INDUSTRIAL  USERS  AND 
PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF THE EQUIPMENT. 
AIM shall honor valid warranty claims on warranted equipment for a period of 

ONE YEAR 

in the event of 

such a failure within the warranty time period.  All warranty time periods start on the date manufacture 
of the equipment and not to exceed one year after the equipment is shipped to a distributor or retail 
customer. 
Within  the  applicable  warranty  period  AIM  will  repair  or  replace  any  warranted  parts  or  components 
that fail due to such defects in material or workmanship.  AIM must be notified in writing within thirty 
(30)  days of  such  defect or  failure,  at which  time  AIM  will  provide  instructions  on  the warranty  claim 
procedures to be followed. 

AIM’s Limited Warranty shall NOT apply to:

 

1.

 

Consumable components or parts that fail due to normal wear.  

2.

 

Items  furnished  by  AIM  but  manufactured  by  others.      These  items  are  covered  by  the 

manufacturer’s warranty, if any.

 

3.

 

Equipment  that  has  been modified  by  any  party  other  than  AIM, or equipment  that  has  been 
improperly  installed,  improperly  operated  or  misused  based  upon  industry  standards,  or 
equipment which has not had reasonable and necessary maintenance, or equipment which has 
been used for operation outside of the specifications for the equipment. 

In  the  event  of  a  warranty  claim  covered  by  this  warranty,  the  exclusive  remedies  shall  be,  at  AIM’s 

option:  

1.

 

Repair,  

2.

 

Replacement,   

3.

 

The  reasonable  cost  of  repair  or  replacement  by  an  authorized  AIM  service  representative 
(where authorized in writing by AIM in appropriate cases), or  

4.

 

Payment  of  or  credit  for  the  purchase  price  (less  reasonable  depreciation  based  upon  actual 
use)  upon  return  of 

the  goods  at  customer’s  risk  and  expense.    AIM’s  option  of  repair  or 

replacement  will  be  F.O.B.,  Factory  at  Spokane,  WA,  or  F.O.B.  at  an  AIM  authorized  service 
representative  as  determined  by  AIM.  Therefore,  no  compensation  or  reimbursement  for 
transportation costs of any kind will be allowed. 

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion 
of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not 
apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary 
from state to state. 
In  Canada,  legislation  in  some  provinces  provides  for  certain  additional  warranties  or  remedies  other 
than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set 

Содержание HPM 300
































Отзывы: