ahlsell Innova IGZCAPB100NI-1 Скачать руководство пользователя страница 60

Страница: 60 / 72

DC Inverter U-match Series Cassette Type Unit

5.3 Unit Maintenance

Warning

①

Only professionals are allowed to carry on daily maintenance.

②

Before contacting any wire, make sure power is cut off.

③

Do not let any inflammable objects near the unit.

④

Do not use organic solvent to clean the air conditioner.

⑤

If you need to replace a component, please ask a professional to repair with a

component supplied by the original manufacturer so as to ensure the unit

’

quality.

⑥

Improper operation may get the unit broken, hit by electric shock or cause fire.

⑦

Do not make the air conditioner wet or electric shock may be lead; Ensure that

the air conditioner will not be cleaned by water rinsing under any

circumstance.

Notice

①

Before cleaning, please make sure the unit is stopped. Cut the circuit breaker

and remove the power socket, otherwise, electric shock may occur.

②

Do not wash the air conditioner with water, otherwise fire hazard or electric

shock may occur.

③

When cleaning the filter, please be careful of your steps. If you need to work

high above the ground, please be extremely careful.

Содержание Innova IGZCAPB100NI-1









































































Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды

ahlsell Innova IGZCAPB100NI-1, Руководство пользователя

Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды