ahlsell Innova IGZCAPB100NI-1 Скачать руководство пользователя страница 58

Страница: 58 / 72

DC Inverter U-match Series Cassette Type Unit

Notice:

Check the above items and adopt the corresponding

corrective measures. If the air conditioner continues to function poorly, please
stop the air conditioner immediately and contact innova’s authorized local service
center. Ask our professional service staff to check and repair the unit.

5.2 Error Code

Warning

①

If abnormal things (for example, awful smell) occur, please stop the unit

immediately and disconnect power. Then contact innova

’

s authorized service

center. If the unit continues to run in abnormal situations, it may get damaged

and cause electric shock or fire hazard.

②

Do not repair the air conditioner by yourself. Improper maintenance will cause

electric shock or fire hazard. Please contact innova

’

s authorized service center

and send for professional service staff to repair.

If the display panel or wired control displays an error code, please refer to the

error code meaning stated in the following table.

Number

Error

code Error

E1 Compressor high pressure protection

E2 Indoor anti-freeze protection

E3 Compressor low pressure protection, refrigerant lack

protection and refrigerant colleting mode

E4 Compressor air discharge high-temperature protection

E6 Communication error

Indoor fan error

Water-full protection

F0 Indoor ambient temperature sensor error

F1 Evaporator temperature sensor error

F2 Condenser temperature sensor error

F3 Outdoor ambient temperature sensor error

F4 Discharge temperature sensor error

Wired control temperature sensor error

IDU jumper cap error

IDU or ODU memory chip error

Electric box sensor error

Содержание Innova IGZCAPB100NI-1









































































Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды

ahlsell Innova IGZCAPB100NI-1, Руководство пользователя

Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды