ahlsell Innova IGZCAPB100NI-1 Скачать руководство пользователя страница 13

Страница: 13 / 72

DC Inverter U-match Series Cassette Type Unit

shape, so please hold the base of the unit as well. During installation, be sure to
use the components specified in the instruction manual.

(3) Please use the charging machine specialized for R32 refrigerant; Before

charging, keep the refrigerant tank in an upright position. After charging, stick a
label on the air conditioner saying no excessive charging.

(4) The following tools will be used: 1) Liquid-level gauge; 2) Screwdriver; 3)

Electric driven rotary hammer; 4) Drill; 5) Pipe expander; 6) Torque wrench; 7)
Open-end wrench; 8) Pipe cutter; 9) Leak detector; 10) Vacuum pump; 11)
Pressure gauge; 12) Universal meter; 13) Hexagon wrench; 14) Tapeline.

3.1.2 Selection of Installation Location

WARNING

①

If the outdoor unit will be exposed in strong wind, it must be securely located,

otherwise it may fall down.

②

Install the air conditioner at a place where the inclination is less than 5°.

③

Do not install the unit at a place with direct sunlight.

④

Do not install the unit at a place with leakage of inflammable gas.

Selection of Installation Location for Indoor Unit (Select a location

pursuant to the following condition).

(1) Air inlet and outlet of the indoor unit should be away from obstacles to make

sure the unit’s air flow can reach the entire room. Do not install the unit in a
kitchen or a laundry.

(2) Install the unit in a room without naked flame, fire source or the risk of getting

the refrigerant on fire.

(3) Select a location that can withstand 4 times the unit weight without increasing

operating noise and vibration.

(4) The installation location must be level.
(5) The indoor piping length and wiring length should be within the allowable

range.

(6) Select a place that can easily drain condensate and connect to the drain

system of the air conditioner.

(7) If hoisting screw bolts are to be used, check whether the installation location is

safe enough. If not safe, reinforce the location before installation.

Содержание Innova IGZCAPB100NI-1









































































Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды

ahlsell Innova IGZCAPB100NI-1, Руководство пользователя

Результаты поиска

Содержание Innova IGZCAPB100NI-1

Отзывы:

Похожие инструкции для Innova IGZCAPB100NI-1

Бренды по названию

Популярные бренды