ahlsell Innova IGZCAPB100NI-1 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 72

background image

DC Inverter U-match Series Cassette Type Unit

18

Model

H(mm)

IGZCAPS35NI-1

295

IGZCAPS50NI-1

295

IGZCAPS71NI-1

270

IGZCAPB85NI-1

270

IGZCAPB100NI-1

270

IGZCAPB125NI-1

320

IGZCAPB140NI-1

320

IGZCAPB160NI-1

320

3.2 Unit Installation

3.2.1 Indoor Unit Installation

In order to make the front panel cover 20mm of the ceiling, the distance

between the ceiling and the unit should be 35mm or less. If the distance between
the ceiling and the unit is above 35mm, add some ceiling material to shorten the
distance. See the following diagram.

Ceiling material

≤35mm

≤35mm

3.2.1.1 Hoisting the Main Body Unit

NOTICE

Please tightly screw up the nuts and bolts to prevent the air conditioner from falling.

(1) Installing the Suspension Bolts.

1) Using the installation template, drill holes for bolts (four holes).
2) Install the bolts to the ceiling at a place strong enough to hang the unit.

Mark the bolt positions from the installation template. With a concrete drill,
drill for 12.7 mm (1/2") diameter holes.

3) Insert the anchor bolts into the drilled holes, and drive the pins completely

into the anchor bolts with a hammer.

«
...
20
21
22
23
24
...
»

Содержание Innova IGZCAPB100NI-1









































































Отзывы:

Нет отзывов

Похожие инструкции для Innova IGZCAPB100NI-1

Бренд: Bard Страницы: 8

Бренд: York Страницы: 24

Бренд: York Страницы: 56

Бренд: York Страницы: 385

Бренд: Daikin Страницы: 17

Бренд: Payne Страницы: 32

Бренд: Haier Страницы: 17

Бренд: O3ZY Страницы: 15

SYSVRF JOINT OUT 02 HP

Бренд: SystemAir Страницы: 2

Бренд: Clatronic Страницы: 62

Бренд: edc Страницы: 46

Бренд: SheerAIRE Страницы: 24

38NY009-012 Series

Бренд: Carrier Страницы: 9

Бренд: Midea Страницы: 72

641415.30 series

Бренд: Dometic Страницы: 18

Бренд: Friedrich Страницы: 2

Бренд: Midea Страницы: 19

Бренд: Marstair Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды