1
Safety Instructions
Hydrostatic implement carrier agria 5900 Cyclone
11
Do not use assist-starting liquids when
using electrical assist-starting devices
(jumper cable). Danger of explosion!
Operation
Never leave the operator's position at the
steering bar while working.
Never adjust operator bars while work is
in progress
– risk of accident!
For all work with the device, especially
when turning, the machine operator must
maintain the distance from the device
shown by the bars.
Riding on the implement during operation
or in transport is not permitted.
In the event of any clogging to the work
equipment or add-on device, the engine
must be stopped and the work equipment
or add-on device must be cleaned with
appropriate tools. There may be tension
in the drive train as a result of the block-
age, which is why you should resolve the
blockage carefully.
In the event of any damage to the ma-
chine or the add-on device, shut down the
engine immediately and have the dam-
age repaired.
In the event of any malfunctions to the
steering, stop and park the machine im-
mediately. Have the fault resolved with-
out delay.
If there is a risk of skidding down on slop-
ing terrain, then the machine must be
held by an attendant using a bar or a
rope. The attendant must be located
above the machine at a safe distance
from the work equipment.
Work across the slope along contour
lines if possible. If possible, turn the ma-
chine in uphill direction.
Finishing work
Never leave the machine unsupervised
while the engine is running.
Switch the engine off before leaving the
machine. Then close the fuel tap(s) (if
present).
Take care not to park the hot machine in
the blazing sun.
Protect the machine against unauthor-
ized use. In ignition key models, remove
the ignition key; otherwise, remove the
spark plug connector.
Implements
Attach an implement only when engine
and implement drive are switched off.
Prior to attaching and starting the imple-
ment, read and observe the operating in-
structions of the implement.
Use adequate tools and wear gloves to
replace implements and parts thereof.
Put the supporting equipment to the
proper position and ensure stability when
you attach or remove an implement.
Secure machine and implements against
rolling away (parking brake - if installed,
wheel chocks).
There is a risk of injuries when you attach
an implement. Take special care.
Attach an implement in accordance with
the regulations and only at the specified
fixtures.
Always switch off the working tools during
a transport ride or when you drive to ad-
jacent working areas.
Secure machine and implement against
unauthorized use and rolling away when
you leave it. If necessary, install transport
or safety equipment, and put it in protec-
tive position.
Mowing equipment
When handled improperly, the sharp
edges of the mower knives can cause
significant injuries. Always wear protec-
tive gloves when you work on the knives.
Ensure that the screwing movements are
away from the cutting edges when you re-
place a knife and loosen or secure the
knife driver.
Wear protective goggles and protective
gloves when you grind the knives.
Содержание Cyclone 5900
