Agri-Fab LST42F Скачать руководство пользователя страница 9

Страница: 9 / 36

STEP 7: (SEE FIGURE 7)
• Attach the cable bracket to the double hole in the

clutch frame as shown, using a 5/16" x 3/4" carriage
bolt and a 5/16" nylock nut. Place the bolt in the front
hole of the bracket and in the end of the hole closest

to the pulley.

Do not tighten yet.

FIGURE 7

FIGURE 9

STEP 9: (SEE FIGURE 9)
• Attach each rear pulley frame bracket to the inside

of the clutch frame using two 5/16" x 3/4" hex bolts,
5/16" washers and 5/16" nylock nuts.

• Attach each front pulley frame bracket to the inside of

the clutch frame using two 5/16" x 1" hex bolts, four
5/16" washers and two 5/16" nylock nuts.

THIS SECTION IS FOR TRACTORS WITH A
MANUAL ATTACHMENT CLUTCH

If your tractor has an electric attachment clutch go to
step 14 on page 11.

FIGURE 10

STOP

Did you select the correct drive belt for your
tractor? Using the wrong length belt may
cause premature bearing or belt failure.

STEP 10: (SEE FIGURE 10)
• Two different length drive belts are included with your

snow thrower. Use the longer, 56" drive belt (

#48138

)

on tractors with manual attachment clutches.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.
Place the belt to the inside of the other flat idler pulley.

FIGURE 8

STEP 8: (SEE FIGURE 8)
• Attach the pulley (long end of hub facing down) and

the large 3/8" spacer to the clutch frame. Use a 3/8" x
3-1/4" hex bolt, a 3/8" washer, a 3/8" lock washer and a
3/8" hex lock nut.

• Install a tensioning chain through the hole shown and

then insert a 3/32" hairpin cotter into the 4th link.

• Attach the chain to the spring on the lower idler arm.

CABLE
BRACKET

5/16" x 3/4"
CARRIAGE BOLT

5/16" NYLOCK
NUT

5/16" x 1"
HEX BOLT

5/16" x 3/4"
HEX BOLT

5/16"
NYLOCK
NUT

5/16" WASHER

(2) 5/16"
WASHERS

HEX BOLTS

(#48138)
DRIVE BELT

FLAT IDLER
PULLEYS

LARGE 3/8" SPACER

3/8" LOCKWASHER

3/8" HEX LOCK NUT

3/8" WASHER

3/8" x 3-1/4"
HEX BOLT

TENSIONING
CHAIN

PULLEY

(long end of
hub down)

3/32" HAIRPIN COTTER
IN 4TH LINK

Содержание LST42F





































Результаты поиска

Содержание LST42F

Отзывы:

Похожие инструкции для LST42F

Бренды по названию

Популярные бренды

Agri-Fab LST42F, Руководство пользователя

Результаты поиска

Содержание LST42F

Отзывы:

Похожие инструкции для LST42F

Бренды по названию

Популярные бренды