Agri-Fab LST42F Скачать руководство пользователя страница 15

Страница: 15 / 36

INSTALLING CLUTCH/IDLER ASSEMBLY

This section covers the installation of the Clutch/Idler

assembly to tractors with attachment clutches that are
either rod operated (p. 15), cable operated (p. 17) or

electric (p. 19). Use the appropriate instructions for your
tractor.

ROD OPERATED MANUAL ATTACHMENT CLUTCH

STEP 29: (SEE FIGURE 29)
• Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

• Screw the trunnion onto the end of the snow thrower

engagement rod.

• Locate the clutch arm (where the mower clutch rod

was connected) underneath the right hand side the

tractor, just to the inside of the suspension arm.

there is an extension

attached to the clutch lever, the

extension, bolt and nut must be removed and stored
with the mower deck.

IMPORTANT: Re-attach the extension

to the clutch

lever before reinstalling the mower deck.

• Position the engagement rod to the inside of the clutch

arm and insert the drilled end of the rod through the
arm. Secure with a 5/64" hairpin cotter.

FIGURE 29

RIGHT SIDE VIEW

ENGAGEMENT ROD

5/64" HAIRPIN
COTTER

TRACTOR'S CLUTCH ARM

SUSPENSION ARM

TRUNNION

REMOVE EXTENSION,
BOLT AND NUT
(IF PRESENT)

STEP 30: (SEE FIGURE 30)
• Attach the two rear pulley frame brackets to the inside

of the clutch/idler assembly using two 5/16" x 1" hex
bolts, eight 5/16" washers and two 5/16" nylock nuts for
each bracket.

• Attach the two front pulley frame brackets to the inside

of the clutch/idler assembly using two 5/16" x 3/4" hex
bolts, 5/16" washers and 5/16" nylock nuts for each
bracket. Add extra washers if needed.

FIGURE 30

FIGURE 31

STOP

Did you choose the correct drive belt for
your tractor? Using the wrong length belt
may cause premature bearing or belt failure.

STEP 31: (SEE FIGURE 31)
• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment
clutches and dual front deck suspension brackets use
the 55" drive belt with

#46989

printed on the outside

of the belt.

DO NOT USE the other belt.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

TENSIONING CHAIN
(lower idler arm)

5/16" x 3/4"
HEX BOLT

5/16" x 1"
HEX BOLT

5/16" NYLOCK NUT

5/16"
WASHER

(4) 5/16" WASHERS

3/32" HAIRPIN
COTTER IN
4th LINK

#46989
DRIVE BELT

FLAT IDLER
PULLEY

HEX BOLTS

• Insert a tensioning chain through the hole shown and

attach it to the spring on the lower idler arm.

• Install a 3/32" hairpin cotter in the 4th link of the chain.

Содержание LST42F





































Результаты поиска

Содержание LST42F

Отзывы:

Похожие инструкции для LST42F

Бренды по названию

Популярные бренды

Agri-Fab LST42F, Руководство пользователя

Результаты поиска

Содержание LST42F

Отзывы:

Похожие инструкции для LST42F

Бренды по названию

Популярные бренды