manualshive.com logo in svg

Agri-Fab LST42F, Руководство пользователя, Страница: 28 / 36

Поделиться
Скачать
Agri-Fab LST42F Скачать руководство пользователя страница 28

28

PARTS TO REMOVE AT END OF SEASON

•  Remove the clutch/idler assembly. (The two hanger 

brackets and the two shoulder bolts may be left 
attached to the tractor frame.)

•  Remove the drive belt from the engine pulley.
•  If you replaced the engine pulley keeper on a manual 

attachment clutch tractor, reinstall the tractor's original 
engine pulley keeper. See figure 33 on page 16 or 

figure 39 on page 18.

•  If you have a rod operated attachment clutch, remove 

the engagement rod from the tractor's clutch arm. See 

figure 29 on page 15. 

•  If a front mounted attachment is to be used, remove 

the side plates from the tractor.  Be sure to assemble 
bolts back into the empty holes in the tractor frame.

STORAGE RECOMMENDATIONS

•  Lower the snow thrower to the ground.
•  Remove the snow thrower from the tractor.
•  Clean the snow thrower thoroughly. Wash off any salt 

deposit which may have dried on the thrower and 

housing.

•  Any bare metal that has become exposed should be 

painted or coated with a light oil to prevent rust.

•  Store in a dry place.

REMOVING THE SPIRAL AUGER HOUSING

•  Lower the snow thrower to the ground.
•  Remove the clevis pins. See figure 54 on page 23.
•  Lock the snow thrower's lift handle in the down 

position to decrease belt tension. 

•  Release the spring tension from the auger belt idler 

arm on the bottom of the clutch/idler assembly.

•  Remove the auger drive belt from the clutch/idler 

assembly. See figure 56 on page 23.

•  Pull the spiral auger housing assembly off of the 

tractor.

STORAGE

ADJUSTING LIFT HEIGHT, LEVELING

The snow thrower is equipped with two threaded lift 

links for adjusting the lift height and leveling of the snow 

thrower in the raised position. 

TO ADJUST THE LIFT HEIGHT:

•  Raise the snow thrower to the highest position. 
•  Check the clearance between the rear of the idler 

bracket (item 39, page 30) and the lift shaft assembly 
(item 1, page 32). A minimum 1/16" clearance in the 
raised position is necessary to avoid possible damage 
to the lift system. 

•  To increase the lift height, tighten the nuts on the 

top of both lift links equally until 3" to 4" of ground 
clearance is obtained. The maximum clearance is 
approximately 4 inches for GT tractors and 3 inches 

for YT tractors. Refer to figure 58 on page 24.

TO LEVEL WHEN RAISED:

•  To keep the snow thrower level in the raised position, 

loosen the nut on the top of the lift link on the high 

side of the snow thrower until the snow thrower is 

approximately level. It is not critical that the snow 
thrower be exactly level in the raised position, it will 

level out when it is lowered to the ground.

Содержание LST42F





































Отзывы:

Нет отзывов