Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 128

Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 96

96

3000 X-Series Oscilloscopes Advanced Training Guide

4

Serial Bus Decoding & Triggering, Search & Navigation, and Segmented Acquisition Labs

long decoded record can be difficult. So let’s now perform an automatic
search to find all occurrences of Error Frames and “form” errors
(non- flagged error conditions). We will then automatically navigate to each
of these error conditions.

23

Push the horizontal position/delay knob to re- position the trigger point
back to center- screen.

24

Set the scope’s timebase to

100.0 ms/div

.

25

Press the

[Search]

front panel key.

26

Press the

Search Edge

softkey; then select

Serial 1 (CAN)

.

27

Press the

Search for

softkey; then select

All Errors

using the Entry knob.

The white triangles near the top of the waveform area mark the time
location of each “found” occurrence of our search operation as shown in

. These frames are also marked in orange in the first/pointer

column of the lister table. Your scope should have found and marked more
than 10 occurrences of this search operation based on a total acquisition
time of 1 second. Note that the number of “found” events is indicated near
the bottom of the display. To automatically navigate to each CAN error,

press the

and

front panel navigation keys.

Figure 70 Using the scope’s automatic Search & Navigation capability to find all

occurrences of CAN errors over a 1 second time span.

«
...
94
95
96
97
98
...
»

Содержание InfiniiVision 3000 X- Series

































































































































Отзывы:

Нет отзывов