Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 68

Страница: 68 / 128

3000 X-Series Oscilloscopes Advanced Training Guide

Advanced Triggering, Search & Navigation, and Segmented Acquisition Labs

Your scope should now be triggering on logic pattern 1110 0110 (D7- D0),
and the top of the sine wave should be centered on- screen as shown in

Figure 47

. In addition to displaying individual digital channels, this scope

can also display all of the digital channels of acquisition in an overlaid
bus display mode while displaying the HEX value of the bus. Let’s now set
up the scope to show the bus display mode.

Press the

[Digital]

front panel key; then press the

Bus

softkey.

Press the

Bus

softkey two times to enable the B1 bus display mode.

Set the scope’s timebase to

20.00 µs/div

Figure 47 Triggering on Pattern = 1110 0110.

Содержание InfiniiVision 3000 X- Series

































































































































Результаты поиска

Содержание InfiniiVision 3000 X- Series

Отзывы:

Agilent Technologies InfiniiVision 3000 X- Series, Руководство по продвинутой подготовке, Страница: 68 / 128

Результаты поиска

Содержание InfiniiVision 3000 X- Series

Отзывы: