manualshive.com logo in svg

Agilent Technologies InfiniiVision 3000 X- Series, Руководство по продвинутой подготовке, Страница: 108 / 128

Поделиться
Скачать
Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 108

108

3000 X-Series Oscilloscopes Advanced Training Guide

4

Serial Bus Decoding & Triggering, Search & Navigation, and Segmented Acquisition Labs

 

Using the default trigger value of arming on right- channel value 

≤

 - 10 and 

then trigger on right- channel value 

≥

 +10, your scope should now be 

triggering on “R: +20” with this byte shown at center- screen similar to 

Figure 81

. Let’s now capture a longer stream of I

2

S traffic and then 

manually search through the captured and decoded record.

26

Press the 

[Serial]

 front panel key.

27

Press the 

Lister

  softkey;  then  turn  the  Entry  knob  to  select 

Serial 1 (I

2

S)

.

28

Set the scope’s timebase to 

10.00 ms/div

.

29

Press 

[Run/Stop]

 to stop repetitive acquisitions.

30

Press the 

Scroll Lister

  softkey;  then  turn  the  Entry  knob  to  manually 

scroll through the lister table.

As you scroll through the data, note that waveforms “track”. This means 
that the frame that the arrow points to in the lister table corresponds to 
the waveforms that are positioned at center- screen. If you want to zoom 

in on a particular I

2

S frame of data, either push the Entry knob, or press 

the 

Zoom to Selection

 softkey. Let’s now perform an automatic search to find 

every occurrence of Right- channel > +10.  We  will  then  automatically 
navigate to each of these occurrences.

31

Push the horizontal position/delay knob to re- position the trigger point 
back to center- screen.

32

Set the scope’s timebase to 

10.00 ms/div

.

33

Press the 

[Search]

 front panel key.

Figure 81 Triggering on I

2

S right-channel = +20.

Содержание InfiniiVision 3000 X- Series

































































































































Отзывы:

Нет отзывов