Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 128

Agilent Technologies InfiniiVision 3000 X- Series Скачать руководство пользователя страница 82

82

3000 X-Series Oscilloscopes Advanced Training Guide

4

Serial Bus Decoding & Triggering, Search & Navigation, and Segmented Acquisition Labs

Your scope should now be triggering on MOSI data = 03

HEX

with this byte

shown at center- screen similar to

. Let’s now capture a very long

stream of SPI traffic and then manually search through the captured and
decoded record.

30

Press the

[Serial]

front panel key.

31

Press the

Lister

softkey; then turn the Entry knob to select

Serial 1 (SPI)

.

32

Set the scope’s timebase to

20.00 ms/div

.

33

Press

[Run/Stop]

to stop repetitive acquisitions.

34

Press the

Scroll Lister

softkey; then turn the Entry knob to manually

scroll through the lister table.

As you scroll through the data, note that waveforms “track”. This means
that the frame that the arrow points to in the lister table corresponds to
the waveforms that are positioned at center- screen. If you want to zoom
in on a particular SPI frame of data, either push the Entry knob, or press
the

Zoom to Selection

softkey. Let’s now perform an automatic search to find

every occurrence of MOSI data = 03

HEX

. We will then automatically

navigate to each of these occurrences.

35

Push the horizontal position/delay knob to re- position the trigger point
back to center- screen.

36

Set the scope’s timebase to

20.00 ms/div

.

37

Press the

[Search]

front panel key.

38

Press the

Search Edge

softkey; then select

Serial 1 (SPI)

.

Figure 57 Triggering on MOSI data = 03

HEX

.

«
...
80
81
82
83
84
...
»

Содержание InfiniiVision 3000 X- Series

































































































































Отзывы:

Нет отзывов