manualshive.com logo in svg

Agilent Technologies G3440-68011, Руководство по установке

Поделиться
Скачать
Agilent Technologies G3440-68011 Скачать руководство пользователя страница 7

Agilent G3440-68011 Micro Electron Capture (µECD) 3rd Detector

Installation Instructions

7

Figure 6

Aux zone/valve box cable and solenoid valve bracket install

4

Align the solenoid valve bracket so the cables are coming from the bottom 
of the bracket and the screws are located at the top over the screw holes in 
the frame. See 

Figure 6

.

5

Tighten the captive screws into the frame.

6

Connect the MSD heated zone cable (long) to the bracket in the first (A1) or 
last (A2) position. Record its position for use during configuration.

7

Route the MSD heated zone cable (long) across the top of the GC oven. Pass 
it under any detector gas lines and through the channels to the right side of 
the instrument. See 

Figure 7

.

Figure 7

Route the MSD heater cable across the GC oven top (view from front of GC)

8

On the left side of the oven top, unfasten the grommet and include the MSD 
heated zone long cable. See 

Figure 8

. Refasten the grommet.

AI

V1

V2

V3

V4

A2

Solenoid valve 
bracket

Bracket captive 
screws

MSD heated zone 
cable (installed in 
first position)

Aux zone/valve box 
cable connection at P22

Содержание G3440-68011



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды