Agilent Technologies E8257D Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 33

Agilent Technologies E8257D Скачать руководство пользователя страница 30

User’s and Service Guide

23

E8257D Option HAR

Safety and Regulatory Information

Servicing

Warnings applicable to this instrument

.

WARNING

To prevent electrical shock, disconnect the

Agilent Technologies

E8257D Option HAR

from the mains before cleaning. Use a dry cloth

or one slightly dampened with water to clean the external case parts.
Do not attempt to clean internally.

WARNING

This is a Safety Class I product (provided with a protective earthing
ground incorporated in the power cord). The mains plug shall be
inserted only into a socket outlet provided with a protective earth
contact. Any interruption of the protective conductor, inside or
outside the product is likely to make the product dangerous.
Intentional interruption is prohibited.

WARNING

These servicing instructions are for use by qualified personnel only.

WARNING

The opening of covers or removal of parts is likely to expose
dangerous voltages. Disconnect the instrument from all voltage
sources while it is being opened.

WARNING

This product is designed for use in Installation Category II and
Pollution Degree 2 per IEC 61010-1: 2001.

WARNING

No operator serviceable parts inside. Refer servicing to qualified
personnel.

WARNING

If this product is not used as specified, the protection provided by
the equipment could be impaired. This product must be used in a
normal condition (in which all means for protection are intact) only.

«
...
28
29
30
31
32
...
»

Содержание E8257D


































Отзывы:

Нет отзывов