Agilent Technologies 54621A Скачать руководство пользователя

Страница: 89 / 118

5-13

Troubleshooting

To run the internal self-tests

To run the internal self-tests

Self Test performs a series of internal procedures to verify that the oscilloscope
and any attached module are operating properly.

It is recommended that you run the Self Test:

• after experiencing abnormal operation

• for additional information to better describe an oscilloscope failure

• to verify proper operation after the oscilloscope has been repaired

Successfully passing Self Test does not guarantee 100% of the oscilloscope’s
functionality. Self Test is designed to provide an 80% confidence level that the
oscilloscope is operating properly.

Press the

Utility

key, then press the

Service

softkey.

Begin the internal self tests by pressing the

Self Test

softkey.

The oscilloscope will display the message “Running self tests” on the screen.

The oscilloscope will then display one of the following messages on the
screen indicating the status of the self-tests:

• Self Tests Passed.

• Self Tests Failed.

service.book Page 13 Wednesday, December 18, 2002 8:35 AM

Содержание 54621A























































































































Результаты поиска

Содержание 54621A

Отзывы:

Похожие инструкции для 54621A

Бренды по названию

Популярные бренды

Agilent Technologies 54621A, Руководство по обслуживанию

Результаты поиска

Содержание 54621A

Отзывы:

Похожие инструкции для 54621A

Бренды по названию

Популярные бренды