Agilent Technologies 54621A Скачать руководство пользователя | Manualshive

Страница: 36 / 118

background image

2- 12

Preparing the Oscilloscope for Use

To connect a printer

To connect a printer

The oscilloscope connects to a parallel printer through the Parallel output
connector on the rear of the oscilloscope. You will need a parallel printer cable
to connect to the printer.

1 Attach the 25-pin small “D” connector to the Parallel output connector

on the rear of the oscilloscope. Tighten the thumbscrews on the cable
connector to secure the cable.

2 Attach the larger 36-pin “D” connector to the printer.

3 Set up the printer configuration on the oscilloscope.

a Press the

Utility

key, then press the

Print Confg

softkey.

b Press the

Print to:

softkey and set the interface to

Parallel

.

c Press the

Format

softkey and select your printer format from the list.

For more information on printer configuration, refer to the “Utilities” chapter
in the User’s Guide.

To connect an RS-232 cable

The oscilloscope can be connected to a controller or a PC through the RS-232
connector on the rear of the oscilloscope. An RS-232 cable is shipped with each
54622A/22D/24A oscilloscope and may be purchased for the 54621A/21D
oscilloscopes.

1 Attach the 9-pin “D” connector on the RS-232 cable to the RS-232

connector on the rear of the oscilloscope. Tighten the thumbscrews on
the cable connector to secure the cable

2 Attach the other end of the cable to your controller or pc.

3 Set up the RS-232 configuration on the oscilloscope.

a Press the

Utility

key, then press the

I/O

softkey.

b Press the

Controller

softkey and select

RS-232

.

c Press the

Baud

softkey and set the baud rate to match your controller or pc.

d Press the

XON DTR

softkey and set the handshake to match your controller

or pc.

For more information on RS-232 configuration, refer to the “Utilities” chapter
in the User’s Guide.

service.book Page 12 Wednesday, December 18, 2002 8:35 AM

«
...
34
35
36
37
38
...
»

Содержание 54621A























































































































Отзывы:

Нет отзывов

Похожие инструкции для 54621A

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: Kamstrup Страницы: 100

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 12

Бренд: Kamstrup Страницы: 60

Бренд: Kamstrup Страницы: 136

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 155

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 2

Бренд: NanoPhotometer Страницы: 133

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды