AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя | Manualshive

Страница: 30 / 74

background image

30

BU-0101704 R3

Position the Underfloor Auger on the Bin Floor

Lift the underfloor auger and place it on the bin floor. Use proper lifting equipment (see

Section 5.4 – Required

Lifting Equipment on page 24

).

Note

The bin unload does not need to be located at the center point of the bin at this stage of assembly.

Remove the Lower Gearbox Controls

Remove the lower gearbox controls to allow for the underfloor auger to clear the bin wall cutout and to enable
the bin adapter to slide over the lower gearbox control rod.

1. Remove the 1/4” x 1-1/2” bolts (1) and nylon locknuts (2) from the coupler (3) of the lower gearbox control

rod (see

Figure 11.

Unfasten the Coupler from the Gearbox Control Rod

2. Remove the 7/16” x 1–1/4” bolt (5), locknut (6), and bushing (7). Remove the gearbox shift lever (8) from

the underfloor auger (see

).

2

3

1

4

2

3

1

4

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

«
...
28
29
30
31
32
...
»

Содержание Westeel EasyFlow2 100 Series











































































Отзывы:

Нет отзывов

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренд: Qingdao H.Y Страницы: 6

Бренд: Rain Bird Страницы: 2

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Parkside Страницы: 95

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренд: GE Страницы: 18

Бренд: Bartscher Страницы: 61

Бренд: Barreto Страницы: 16

Implantmed SI-1010

Бренд: W&H Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды